Tektronix TDS784D Opt 13/1F/HD/2C/2F/2M/3C/4C 1GHz 4GS/s
This TDS784D is in good condition and has options 13, 1F, HD, 2F, 2M, 2C, 3C and 4C installed according to splash screen. It does not come with the P6701B or P6703B probes included. They are available for an additional fee. It passes all self testing, self calibration, and functional checks. This unit is missing the label that is normally on the front bezel of the scope. Also the front bezel has a repaired crack as can be seen in the last photo. The rear bezel has 2 hairline cracks that have been repaired with superglue. All the cracks in the bezels have been thoroughly repaired. The CRT has some slight burn marks.
Some options are defined here:
Tektronix DPO Oscilloscope per TDS operator manual
Model TDS784D
Includes the following options:
13 - RS232/Centronics Hardcopy Interfaces
1F - Floppy Disc Drive
HD - Internal Hard Disc Drive
2M - Add'l 2M/Channel Memory Length
2F - Extended Waveform Math
2C - Communications Signal Analyzer
3C - P6701B with system calibration
Oscilloscope comes with a P6701B and calibrated short-wavelength optical reference
receiver on channel 1. (Option applies to TDS 500D & TDS 700D only, except TDS 794D.)
4C - Fibre Channel Optical Reference
P6703B with system calibration ,Oscilloscope comes with a P6703B and calibrated long-wavelength optical reference
receiver on channel 1. (Option applies to TDS 500D & TDS 700D only, except TDS 794D.)
1 GHz Bandwidth, 4 Channels
Sample Rates to 4 GS/sRecord Lengths to 8 M PointsUp to 200,000 Waveforms per Second8-Bit Vertical Resolution, >11 Bits with Averaging and >13 Bits with Hi-res1 ns Peak DetectFloppy Disk StorageIomega Zip and Zip Plus Drive CompatibleAdvanced Triggering29 Automatic Measurements and Measurement StatisticsFFT, Advanced Math, Histograms, Limit TestFastFrame Time StampCommunication Signal Analysis, Including Mask Testing and SONET/SDH and Fibre Channel Optical Reference ReceiversGPIB
This item is offered with a 30 day warranty or more.
Any item with a price of $10000.00 or more will qualify for 90 day warranty with full price purchase. All seals must be intact for warranty to apply.
US POWER AND TEST EQUIPMENT INC. , TERMS OF SALE
FREIGHT POLICY
Products are shipped F.O.B. origin to customer's single location located in the contiguous United States, in accordance with US Power and Test Equipment Inc. 's freight schedule. Receipts for shipping will not be furnished. COD shipments are not permitted. Other terms and conditions may apply for other than standard ground delivery (“Other Freight Services”), including without limitation, expedited same day delivery, air freight, freight collect, export orders, sourced products, non-stock products hazardous materials, customer's carrier, shipments outside the contiguous U.S. or other special handling by the carrier. Any charges incurred for other Freight Services must be paid by customer. Fuel surcharges may be applied. Title and risk of loss pass to customer upon tender of shipment to the carrier. If the product is damaged in transit, customer's only recourse is to file a claim with the carrier.
PRODUCT WARRANTY POLICY
Products Damaged in Shipment
Products damaged in shipment will be repaired or replaced at no cost to customer if US Power and Test Equipment Inc. is notified within 10 days of delivery and shipment was made using sellers shipping account. Customer should immediately notify carrier of any visible damages upon delivery.
Limited Warranty Period for Used Products
US Power and Test Equipment Inc. warrants used products against defects in materials and workmanship under normal use for a period of one (1) year after the date of purchase from US Power and Test Equipment Inc., unless otherwise stated, or in the case of haz-mat, sourced, or custom products. provided that US Power and Test Equipment Inc. accepts the product for return during the limited warranty period, US Power and Test Equipment Inc. may, at its option: (i) repair; (ii) replace; or (iii) refund the amount paid by customer. US Power and Test Equipment Inc.'s repair, replacement, or refund of amounts paid by customer for the product, shall be customer's sole and exclusive remedy.
Warranty Disclaimer and Limitations of Liability to All Customers
Except as set forth herein and where applicable, no warranty or affirmation of fact or description, express or implied, is made or authorized by US Power and Test Equipment Inc. . US Power and Test Equipment Inc. disclaims any express or implied warranties of merchantability, fitness for a particular purpose or noninfringement of intellectual property rights. US Power and Test Equipment Inc. also disclaims any liability for claims arising out of product misuse, improper product selection, improper installation, product modification, mis-repair or mis-application. Any liability for consequential, incidental, special, exemplary, or punitive damages is expressly disclaimed to the extent permissible. US Power and Test Equipment Inc. 's liability in all events is limited to the purchase price paid for the product that gives rise to any liability.
Return Policy
To return a product during the Limited Warranty Period (30 days after date of purchase), customer must call 760-473-1732 for a return authorization number. Each return authorization number is valid for thirty (30) days. There is no restocking fee, except as otherwise noted herein, if products are returned within the Limited Warranty Period, shipping prepaid, and be unused, undamaged, new condition, with original packaging and all contents including manufacturer's original packaging unblemished and all accessories, manuals and warranties included. Test and Measurement equipment will incur a restocking fee of 20% if the seal on the box has been opened. Customer must include a copy of the packing list or invoice with a reason for the return. Late returns and incomplete returns will incur a 20%, or higher, restocking fee. Customer will waive and forfeit any and all rights to return any products, if the products have been modified in any way including; but not limited to, hardware or software changes, updates, deletions, removal or replacement of any parts, software or firmware; or modifications of any other kind.
